Add Car Agent Device firmware (LILYGO TTGO T-SIM7600, ESP32/SIM7600)
ESP32 + SIM7600 cellular firmware for the in-car agent device: WiFi/AP provisioning with a web admin page, GPRS/LTE connectivity, and IMEI-based identification. The hardcoded default WiFi password has been replaced with a YOUR-WIFI-PASSWORD placeholder so no real credential enters git history. Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
This commit is contained in:
tajniak81
co-authored by
Claude Opus 4.8
Claude Opus 4.8
parent
19a7d48feb
commit
318e9c1670
@@ -0,0 +1,473 @@
|
||||
/**************************************************************
|
||||
|
||||
TinyGSM Getting Started guide:
|
||||
https://tiny.cc/tinygsm-readme
|
||||
|
||||
NOTE:
|
||||
Some of the functions may be unavailable for your modem.
|
||||
Just comment them out.
|
||||
https://simcom.ee/documents/SIM7600C/SIM7500_SIM7600%20Series_AT%20Command%20Manual_V1.01.pdf
|
||||
**************************************************************/
|
||||
|
||||
#define TINY_GSM_MODEM_SIM7600
|
||||
|
||||
// Set serial for debug console (to the Serial Monitor, default speed 115200)
|
||||
#define SerialMon Serial
|
||||
|
||||
// Set serial for AT commands (to the module)
|
||||
// Use Hardware Serial on Mega, Leonardo, Micro
|
||||
#define SerialAT Serial1
|
||||
|
||||
// See all AT commands, if wanted
|
||||
#define DUMP_AT_COMMANDS
|
||||
|
||||
// Define the serial console for debug prints, if needed
|
||||
#define TINY_GSM_DEBUG SerialMon
|
||||
|
||||
/*
|
||||
Tests enabled
|
||||
*/
|
||||
#define TINY_GSM_TEST_GPRS true
|
||||
#define TINY_GSM_TEST_TCP true
|
||||
// #define TINY_GSM_TEST_CALL true
|
||||
// #define TINY_GSM_TEST_SMS true
|
||||
// #define TINY_GSM_TEST_USSD true
|
||||
// #define TINY_GSM_TEST_TEMPERATURE true
|
||||
// #define TINY_GSM_TEST_TIME true
|
||||
#define TINY_GSM_TEST_GPS true
|
||||
// powerdown modem after tests
|
||||
#define TINY_GSM_POWERDOWN true
|
||||
// #define TEST_RING_RI_PIN true
|
||||
|
||||
// set GSM PIN, if any
|
||||
#define GSM_PIN ""
|
||||
|
||||
// Set phone numbers, if you want to test SMS and Calls
|
||||
// #define SMS_TARGET "+380xxxxxxxxx"
|
||||
// #define CALL_TARGET "+380xxxxxxxxx"
|
||||
|
||||
#define uS_TO_S_FACTOR 1000000ULL /* Conversion factor for micro seconds to seconds */
|
||||
#define TIME_TO_SLEEP 30 /* Time ESP32 will go to sleep (in seconds) */
|
||||
|
||||
#define UART_BAUD 115200
|
||||
|
||||
#define MODEM_TX 27
|
||||
#define MODEM_RX 26
|
||||
#define MODEM_PWRKEY 4
|
||||
#define MODEM_DTR 32
|
||||
#define MODEM_RI 33
|
||||
#define MODEM_FLIGHT 25
|
||||
#define MODEM_STATUS 34
|
||||
|
||||
#define SD_MISO 2
|
||||
#define SD_MOSI 15
|
||||
#define SD_SCLK 14
|
||||
#define SD_CS 13
|
||||
|
||||
#define LED_PIN 12
|
||||
|
||||
// Your GPRS credentials, if any
|
||||
const char apn[] = "YourAPN";
|
||||
// const char apn[] = "ibasis.iot";
|
||||
const char gprsUser[] = "";
|
||||
const char gprsPass[] = "";
|
||||
|
||||
// Server details to test TCP/SSL
|
||||
const char server[] = "vsh.pp.ua";
|
||||
const char resource[] = "/TinyGSM/logo.txt";
|
||||
|
||||
#include <SPI.h>
|
||||
#include <SD.h>
|
||||
#include <Ticker.h>
|
||||
#include <TinyGsmClient.h>
|
||||
//#include "utilities.h"
|
||||
|
||||
#ifdef DUMP_AT_COMMANDS
|
||||
#include <StreamDebugger.h>
|
||||
StreamDebugger debugger(SerialAT, SerialMon);
|
||||
TinyGsm modem(debugger);
|
||||
#else
|
||||
TinyGsm modem(SerialAT);
|
||||
#endif
|
||||
|
||||
void setup()
|
||||
{
|
||||
// Set console baud rate
|
||||
SerialMon.begin(115200);
|
||||
delay(10);
|
||||
|
||||
// Set GSM module baud rate
|
||||
SerialAT.begin(UART_BAUD, SERIAL_8N1, MODEM_RX, MODEM_TX);
|
||||
|
||||
/*
|
||||
The indicator light of the board can be controlled
|
||||
*/
|
||||
pinMode(LED_PIN, OUTPUT);
|
||||
digitalWrite(LED_PIN, HIGH);
|
||||
|
||||
/*
|
||||
MODEM_PWRKEY IO:4 The power-on signal of the modulator must be given to it,
|
||||
otherwise the modulator will not reply when the command is sent
|
||||
*/
|
||||
pinMode(MODEM_PWRKEY, OUTPUT);
|
||||
digitalWrite(MODEM_PWRKEY, HIGH);
|
||||
delay(300); //Need delay
|
||||
digitalWrite(MODEM_PWRKEY, LOW);
|
||||
|
||||
/*
|
||||
MODEM_FLIGHT IO:25 Modulator flight mode control,
|
||||
need to enable modulator, this pin must be set to high
|
||||
*/
|
||||
pinMode(MODEM_FLIGHT, OUTPUT);
|
||||
digitalWrite(MODEM_FLIGHT, HIGH);
|
||||
|
||||
//Initialize SDCard
|
||||
SPI.begin(SD_SCLK, SD_MISO, SD_MOSI, SD_CS);
|
||||
if (!SD.begin(SD_CS)) {
|
||||
Serial.println("SDCard MOUNT FAIL");
|
||||
} else {
|
||||
uint32_t cardSize = SD.cardSize() / (1024 * 1024);
|
||||
String str = "SDCard Size: " + String(cardSize) + "MB";
|
||||
Serial.println(str);
|
||||
}
|
||||
|
||||
|
||||
|
||||
// Uncomment below will perform loopback test
|
||||
// while (1) {
|
||||
// while (SerialMon.available()) {
|
||||
// SerialAT.write(SerialMon.read());
|
||||
// }
|
||||
// while (SerialAT.available()) {
|
||||
// SerialMon.write(SerialAT.read());
|
||||
// }
|
||||
// }
|
||||
}
|
||||
|
||||
void light_sleep(uint32_t sec )
|
||||
{
|
||||
esp_sleep_enable_timer_wakeup(sec * 1000000ULL);
|
||||
esp_light_sleep_start();
|
||||
}
|
||||
|
||||
void loop()
|
||||
{
|
||||
bool res ;
|
||||
|
||||
// Restart takes quite some time
|
||||
// To skip it, call init() instead of restart()
|
||||
DBG("Initializing modem...");
|
||||
if (!modem.init()) {
|
||||
DBG("Failed to restart modem, delaying 10s and retrying");
|
||||
return;
|
||||
}
|
||||
//
|
||||
// // Restart takes quite some time
|
||||
// // To skip it, call init() instead of restart()
|
||||
// DBG("Initializing modem...");
|
||||
// if (!modem.restart()) {
|
||||
// DBG("Failed to restart modem, delaying 10s and retrying");
|
||||
// // restart autobaud in case GSM just rebooted
|
||||
// return;
|
||||
// }
|
||||
|
||||
#if TINY_GSM_TEST_GPRS
|
||||
/* Preferred mode selection : AT+CNMP
|
||||
2 – Automatic
|
||||
13 – GSM Only
|
||||
14 – WCDMA Only
|
||||
38 – LTE Only
|
||||
59 – TDS-CDMA Only
|
||||
9 – CDMA Only
|
||||
10 – EVDO Only
|
||||
19 – GSM+WCDMA Only
|
||||
22 – CDMA+EVDO Only
|
||||
48 – Any but LTE
|
||||
60 – GSM+TDSCDMA Only
|
||||
63 – GSM+WCDMA+TDSCDMA Only
|
||||
67 – CDMA+EVDO+GSM+WCDMA+TDSCDMA Only
|
||||
39 – GSM+WCDMA+LTE Only
|
||||
51 – GSM+LTE Only
|
||||
54 – WCDMA+LTE Only
|
||||
*/
|
||||
String ret;
|
||||
// do {
|
||||
// ret = modem.setNetworkMode(2);
|
||||
// delay(500);
|
||||
// } while (ret != "OK");
|
||||
ret = modem.setNetworkMode(2);
|
||||
DBG("setNetworkMode:", ret);
|
||||
|
||||
|
||||
//https://github.com/vshymanskyy/TinyGSM/pull/405
|
||||
uint8_t mode = modem.getGNSSMode();
|
||||
DBG("GNSS Mode:", mode);
|
||||
|
||||
/**
|
||||
CGNSSMODE: <gnss_mode>,<dpo_mode>
|
||||
This command is used to configure GPS, GLONASS, BEIDOU and QZSS support mode.
|
||||
gnss_mode:
|
||||
0 : GLONASS
|
||||
1 : BEIDOU
|
||||
2 : GALILEO
|
||||
3 : QZSS
|
||||
dpo_mode :
|
||||
0 disable
|
||||
1 enable
|
||||
*/
|
||||
modem.setGNSSMode(1, 1);
|
||||
light_sleep(1);
|
||||
|
||||
String name = modem.getModemName();
|
||||
DBG("Modem Name:", name);
|
||||
|
||||
String modemInfo = modem.getModemInfo();
|
||||
DBG("Modem Info:", modemInfo);
|
||||
|
||||
// Unlock your SIM card with a PIN if needed
|
||||
if (GSM_PIN && modem.getSimStatus() != 3) {
|
||||
modem.simUnlock(GSM_PIN);
|
||||
}
|
||||
|
||||
DBG("Waiting for network...");
|
||||
if (!modem.waitForNetwork(600000L)) {
|
||||
light_sleep(10);
|
||||
return;
|
||||
}
|
||||
|
||||
if (modem.isNetworkConnected()) {
|
||||
DBG("Network connected");
|
||||
}
|
||||
#endif
|
||||
|
||||
|
||||
#if TINY_GSM_TEST_GPRS
|
||||
DBG("Connecting to", apn);
|
||||
if (!modem.gprsConnect(apn, gprsUser, gprsPass)) {
|
||||
light_sleep(10);
|
||||
return;
|
||||
}
|
||||
|
||||
res = modem.isGprsConnected();
|
||||
DBG("GPRS status:", res ? "connected" : "not connected");
|
||||
|
||||
String ccid = modem.getSimCCID();
|
||||
DBG("CCID:", ccid);
|
||||
|
||||
String imei = modem.getIMEI();
|
||||
DBG("IMEI:", imei);
|
||||
|
||||
String imsi = modem.getIMSI();
|
||||
DBG("IMSI:", imsi);
|
||||
|
||||
String cop = modem.getOperator();
|
||||
DBG("Operator:", cop);
|
||||
|
||||
IPAddress local = modem.localIP();
|
||||
DBG("Local IP:", local);
|
||||
|
||||
int csq = modem.getSignalQuality();
|
||||
DBG("Signal quality:", csq);
|
||||
#endif
|
||||
|
||||
#if TINY_GSM_TEST_USSD && defined TINY_GSM_MODEM_HAS_SMS
|
||||
String ussd_balance = modem.sendUSSD("*111#");
|
||||
DBG("Balance (USSD):", ussd_balance);
|
||||
|
||||
String ussd_phone_num = modem.sendUSSD("*161#");
|
||||
DBG("Phone number (USSD):", ussd_phone_num);
|
||||
#endif
|
||||
|
||||
#if TINY_GSM_TEST_TCP && defined TINY_GSM_MODEM_HAS_TCP
|
||||
TinyGsmClient client(modem, 0);
|
||||
const int port = 80;
|
||||
DBG("Connecting to ", server);
|
||||
if (!client.connect(server, port)) {
|
||||
DBG("... failed");
|
||||
} else {
|
||||
// Make a HTTP GET request:
|
||||
client.print(String("GET ") + resource + " HTTP/1.0\r\n");
|
||||
client.print(String("Host: ") + server + "\r\n");
|
||||
client.print("Connection: close\r\n\r\n");
|
||||
|
||||
// Wait for data to arrive
|
||||
uint32_t start = millis();
|
||||
while (client.connected() && !client.available() &&
|
||||
millis() - start < 30000L) {
|
||||
delay(100);
|
||||
};
|
||||
|
||||
// Read data
|
||||
start = millis();
|
||||
while (client.connected() && millis() - start < 5000L) {
|
||||
while (client.available()) {
|
||||
SerialMon.write(client.read());
|
||||
start = millis();
|
||||
}
|
||||
}
|
||||
client.stop();
|
||||
}
|
||||
#endif
|
||||
|
||||
#if TINY_GSM_TEST_CALL && defined(CALL_TARGET)
|
||||
|
||||
DBG("Calling:", CALL_TARGET);
|
||||
SerialAT.println("ATD"CALL_TARGET";");
|
||||
modem.waitResponse();
|
||||
light_sleep(20);
|
||||
#endif
|
||||
|
||||
#if TINY_GSM_TEST_GPS && defined TINY_GSM_MODEM_HAS_GPS
|
||||
DBG("Enabling GPS/GNSS/GLONASS");
|
||||
modem.enableGPS();
|
||||
light_sleep(2);
|
||||
|
||||
float lat2 = 0;
|
||||
float lon2 = 0;
|
||||
float speed2 = 0;
|
||||
float alt2 = 0;
|
||||
int vsat2 = 0;
|
||||
int usat2 = 0;
|
||||
float accuracy2 = 0;
|
||||
int year2 = 0;
|
||||
int month2 = 0;
|
||||
int day2 = 0;
|
||||
int hour2 = 0;
|
||||
int min2 = 0;
|
||||
int sec2 = 0;
|
||||
DBG("Requesting current GPS/GNSS/GLONASS location");
|
||||
for (;;) {
|
||||
digitalWrite(LED_PIN, !digitalRead(LED_PIN));
|
||||
if (modem.getGPS(&lat2, &lon2, &speed2, &alt2, &vsat2, &usat2, &accuracy2,
|
||||
&year2, &month2, &day2, &hour2, &min2, &sec2)) {
|
||||
DBG("Latitude:", String(lat2, 8), "\tLongitude:", String(lon2, 8));
|
||||
DBG("Speed:", speed2, "\tAltitude:", alt2);
|
||||
DBG("Visible Satellites:", vsat2, "\tUsed Satellites:", usat2);
|
||||
DBG("Accuracy:", accuracy2);
|
||||
DBG("Year:", year2, "\tMonth:", month2, "\tDay:", day2);
|
||||
DBG("Hour:", hour2, "\tMinute:", min2, "\tSecond:", sec2);
|
||||
break;
|
||||
} else {
|
||||
light_sleep(2);
|
||||
}
|
||||
}
|
||||
DBG("Retrieving GPS/GNSS/GLONASS location again as a string");
|
||||
String gps_raw = modem.getGPSraw();
|
||||
DBG("GPS/GNSS Based Location String:", gps_raw);
|
||||
DBG("Disabling GPS");
|
||||
modem.disableGPS();
|
||||
#endif
|
||||
|
||||
#if TINY_GSM_TEST_TIME && defined TINY_GSM_MODEM_HAS_TIME
|
||||
int year3 = 0;
|
||||
int month3 = 0;
|
||||
int day3 = 0;
|
||||
int hour3 = 0;
|
||||
int min3 = 0;
|
||||
int sec3 = 0;
|
||||
float timezone = 0;
|
||||
for (int8_t i = 5; i; i--) {
|
||||
DBG("Requesting current network time");
|
||||
if (modem.getNetworkTime(&year3, &month3, &day3, &hour3, &min3, &sec3,
|
||||
&timezone)) {
|
||||
DBG("Year:", year3, "\tMonth:", month3, "\tDay:", day3);
|
||||
DBG("Hour:", hour3, "\tMinute:", min3, "\tSecond:", sec3);
|
||||
DBG("Timezone:", timezone);
|
||||
break;
|
||||
} else {
|
||||
DBG("Couldn't get network time, retrying in 15s.");
|
||||
light_sleep(15);
|
||||
}
|
||||
}
|
||||
DBG("Retrieving time again as a string");
|
||||
String time = modem.getGSMDateTime(DATE_FULL);
|
||||
DBG("Current Network Time:", time);
|
||||
#endif
|
||||
|
||||
#if TINY_GSM_TEST_GPRS
|
||||
modem.gprsDisconnect();
|
||||
light_sleep(5);
|
||||
if (!modem.isGprsConnected()) {
|
||||
DBG("GPRS disconnected");
|
||||
} else {
|
||||
DBG("GPRS disconnect: Failed.");
|
||||
}
|
||||
#endif
|
||||
|
||||
#if TINY_GSM_TEST_TEMPERATURE && defined TINY_GSM_MODEM_HAS_TEMPERATURE
|
||||
float temp = modem.getTemperature();
|
||||
DBG("Chip temperature:", temp);
|
||||
#endif
|
||||
|
||||
#ifdef TEST_RING_RI_PIN
|
||||
#ifdef MODEM_RI
|
||||
//Set RI Pin input
|
||||
pinMode(MODEM_RI, INPUT);
|
||||
|
||||
Serial.println("Wait for call in");
|
||||
//When is no calling ,RI pin is high level
|
||||
while (digitalRead(MODEM_RI)) {
|
||||
Serial.print('.');
|
||||
delay(500);
|
||||
}
|
||||
Serial.println("call in ");
|
||||
|
||||
//Wait for 5 seconds to connect the call
|
||||
delay(5000);
|
||||
|
||||
//Accept call
|
||||
SerialAT.println("ATA");
|
||||
|
||||
// Hang up after 20 seconds of talk time
|
||||
delay(20000);
|
||||
|
||||
SerialAT.println("ATH");
|
||||
|
||||
#endif //MODEM_RI
|
||||
#endif //TEST_RING_RI_PIN
|
||||
|
||||
|
||||
#ifdef MODEM_DTR1
|
||||
|
||||
modem.sleepEnable();
|
||||
|
||||
delay(100);
|
||||
|
||||
// test modem response , res == 0 , modem is sleep
|
||||
res = modem.testAT();
|
||||
Serial.print(" Test AT result -> ");
|
||||
Serial.println(res);
|
||||
|
||||
delay(1000);
|
||||
|
||||
Serial.println("Use DTR Pin Wakeup");
|
||||
pinMode(MODEM_DTR, OUTPUT);
|
||||
//Set DTR Pin low , wakeup modem .
|
||||
digitalWrite(MODEM_DTR, LOW);
|
||||
|
||||
// test modem response , res == 1 , modem is wakeup
|
||||
res = modem.testAT();
|
||||
Serial.print(" Test AT result -> ");
|
||||
Serial.println(res);
|
||||
|
||||
#endif
|
||||
|
||||
|
||||
#if TINY_GSM_POWERDOWN
|
||||
// Try to power-off (modem may decide to restart automatically)
|
||||
// To turn off modem completely, please use Reset/Enable pins
|
||||
modem.poweroff();
|
||||
DBG("Poweroff.");
|
||||
#endif
|
||||
|
||||
SerialMon.printf("End of tests. Enable deep sleep , Will wake up in %d seconds", TIME_TO_SLEEP);
|
||||
|
||||
// Wait for modem to power off
|
||||
light_sleep(5);
|
||||
|
||||
esp_sleep_enable_timer_wakeup(TIME_TO_SLEEP * uS_TO_S_FACTOR);
|
||||
delay(200);
|
||||
esp_deep_sleep_start();
|
||||
|
||||
while (1);
|
||||
}
|
||||
Reference in New Issue
Block a user