Vision radar: graded obstacle sectors around the centre of the video,
the nearest distance per side, the obstacle overhead, and BLOCKED on a
side whose sensors cannot see once the motors run. On aircraft with 360°
sensing, sides without their own readings are filled from the
perception ring. The same sectors sit on the attitude ball's rim, turned
by the heading. Settings > Vision gains Display radar chart and the
braking / sensing distances per direction.
On-screen sticks: the rail's STICKS button hands the aircraft to two
stick pads after a slide-to-confirm. The 25 Hz stream runs natively and
sends zeros once Dart's last command is 300 ms old, so a stalled UI
leaves the aircraft hovering. The sticks close when the remote takes
over, on RTH or on landing. They are simulator-only on aircraft with a
remote unless Settings > General > Developer allows real flights; Spark
and Mavic Air on Wi-Fi may fly them for real. Which MSDK axis is forward
in velocity + body mode is coded from DJI's documentation and must be
checked in the simulator first.
AirSense: a banner for manned aircraft at warning level 2 and up, with
distance, direction and ICAO code; the planes on the map; the full list
in a sheet and Settings > Safety; and the aircraft's own avoidance
action with its countdown.
Fly zones: DJI GEO zones around the aircraft (or the phone) on the map
with their height limits, a banner for FlySafe notices and in/near-zone
states, take-off refused in restricted and locked authorization zones,
self-unlock of authorization zones, the aircraft's licences (enable,
sync from the DJI account, remove all; ground only), and the GEO
database version with an update button.
Tested with unit and widget tests and screenshot renders only; nothing
has run on an aircraft or the simulator yet.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
P6b: a new CalibrationBridge owns every calibration call and publishes
a `calibration` telemetry group (IMU per-unit and per-side progress,
gravity centre, lens, sensor cleaning, RC calibration state and live
sticks). Guided full-screen wizards cover compass, IMU, remote
controller, gimbal auto calibration, lens, sensor cleaning, centre of
gravity, propellers and a vision-sensor guide; gimbal adjust is a
horizon-line overlay on the live video. Every start goes through
SafetyGate.runMaintenance, and closing mid-run stops what the SDK can
stop.
Reachable from Settings > Safety > Calibration & maintenance, the
Aircraft Status calibrate buttons and the gimbal sheet. Not yet run on
an aircraft; the RC key sequence still needs checking per remote.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The "•••" button now opens a right-side glass sheet over the live view
with Safety, Vision, Remote, Video link, Battery, Gimbal and General
tabs. Each row is a one-line spec bound to a KeyManager key: rows hide
when the aircraft does not support their key, writes show at once and
roll back if refused, and ground-only settings lock in flight.
KeyBridge gains argument-less action keys and converts range and LED
settings values. settings_menu_page.dart is retired.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Plan P5: a value bubble on the pitch slider while dragging, press-and-drag
on the video as a speed joystick (re-sent at 10 Hz, zero on release), and a
gimbal settings sheet: mode, 30° extension, yaw follow, recenter / face down /
yaw recenter, roll fine-tune, auto calibration and advanced speed/smoothness
rows gated by the gimbal's capability ranges.
GimbalBridge reports mode, trim, calibration and stop/overload state in the
gimbal telemetry group, and getter-only settings in a new gimbalSettings slow
group. The reported-plus-pending overlay moves out of CameraState into a
SettingsOverlay mixin shared by camera and gimbal.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
One settings table in CameraBridge watches every camera value into the
telemetry tick and backs a generic setCameraValue, so the tabbed camera
menu (Exposure / Photo / Video / Other) is built from row specs and the
camera's own capability ranges. Writes show at once and fall back to what
the camera reports. Adds the quick exposure panel (Auto/A/S/M, ISO slider,
shutter and aperture wheels, EV strip, metered EV in M), a new camera
column with record timer and interval/pano progress, a zoom column for
zoom cameras, tap-to-focus / tap-to-meter, and a live histogram.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Take-off, land, RTH, the landing cancel/confirm and Stop now all go
through one SafetyGate (lib/fly/safety_gate.dart). The gate sorts its
preconditions into blockers and warnings: connection, flight state,
battery against the thresholds, IMU warm-up, compass, critical
diagnostics, GPS, home point, SD card and the RTH battery budget. It
checks again right before sending.
The left rail is now a state machine (lib/fly/action_rail_state.dart):
Take-off becomes Land, then Cancel or Confirm landing. RTH becomes
Cancel RTH. A Stop button shows while an intelligent mode is flying.
Moving the aircraft needs a slide-to-confirm dialog, which can offer
Precision Takeoff or set the RTH altitude. A blocked command shows why
and has no slider. When the pilot is more than 30 m from home, RTH asks
whether to return to them or to the original home point.
The HUD gains an error stack. Its cards can be dismissed, it fits the
space it has, and a new warning triggers haptic feedback. It also gets a
smart-RTH countdown banner with Cancel / Go home now, a forced-landing
banner, and an Aircraft Status sheet. The sheet opens from the status
chip and appears before each connection's first take-off. It offers
Calibrate compass/IMU and Format SD.
On the bridge side this adds precisionTakeOff, setHomeLocation, compass
and IMU calibration start/stop, formatStorage, and compass health in the
telemetry tick.
The classic flight screen stays available until the simulator run passes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
